Proudly
made in
the
USA!
Bommer enjoys a reputation as one of the leading manufacturers of U.S. Postal Service-approved mailboxes. Mailboxes carrying the Bommer trademark have become the standard for multiple-dwelling units: apartment houses, condominiums, dormitories, offices, institutional-type facilities, and private mail box rental centers.
Whenever your requirements include postal specialties, you can feel confident specifying the Bommer line!
FRONT
LOADING - 6200 SERIES STD
4B+ (Call us about current USPS approved 4C Styles)
Access to the compartments for loading is from the
front
through a hinged master door. One door is required for a control lock
which
secures the master frame and cannot be used for mail
distribution.
The
master door may be hinged on the right (standard) or left side.
MODEL 6210 - The 6210 is composed of all size "A" doors. HS6210 has new 4-point locking system.
MODEL 6230 - The 6230 is the same as the 6210 except it contains one or more multiple size doors. A layout must accompany all orders.
MODEL HS-6230 has a new 4-point locking system for maximum mail security.
6200
Series Specifications
COMPARTMENT SIZE (STANDARD):
5"
high x 6" wide x 15" deep.
DOOR LOCK (STANDARD): 5-pin
cam type with 2 keys.
- Optional locks are available, call for information.
DOOR IDENTIFICATION
(STANDARD): 5/8" x 2" number slot with plastic window.
- Optional identification, call for information.
FINISH (STANDARD): 628
natural anodized aluminum.
- Optional enamel and anodized finishes, call for
information.
ALPHABETICAL DIRECTORIES: Side separate and top mounted available.
SNAP-ON TRIM: 9/16" x 1-1/2" extruded aluminum. Standard snap-on trim kit includes four 5' lengths and necessary installation hardware.
CONTROL DOOR LOCK: Prepared for U.S.P.S. lock and provided with slot and baffle for mail collection.
REAR
LOADING
- 6300 SERIES STD 4B+
Access to the compartments for loading is from the
rear.
A lift off rear cover is supplied as standard with an optional hinged
rear
cover available. The rear cover may be omitted on non-U.S.P.S.
installations.
All doors are usable for mail distribution.
MODEL 6310 - The 6310 is composed of all size "A" doors. HS6310 has new 4-point locking system.
MODEL 6330 - 6330 is the same as the 6310 except it contains one or more multiple size doors. A layout must accompany all orders. HS-6330 has new 4-point locking system.
6300
Series Specifications
COMPARTMENT SIZE (STANDARD):
5"
high x 6" wide x 15" deep.
DOOR LOCK (STANDARD):
5-pin cam type with 2 keys.
- Optional locks available, call for information.
DOOR IDENTIFICATION
(STANDARD): 5/8"
x 2" number slot with plastic window.
- Optional identification, call for information.
FINISH (STANDARD):
628
natural anodized aluminum.
- Optional enamel and anodized finishes, call for
information.
ALPHABETICAL DIRECTORIES: Side separate and top mounted available
SNAP-ON TRIM: 9/16" x 1-1/2" extruded aluminum. Standard snap-on trim kit includes four 5' lengths and necessary installation hardware.
DESIGN ASSISTANCE
Our engineering staff is available to architects and
specification writers in the planning of mail distribution facilities
and
the specifying of mailboxes and related items. We also offer our
assistance
to apartment owners and managers in helping to determine their
requirements
in accordance with the latest U.S.P.S. regulations.
ALL
MAILBOXES
GENERAL: Furnish
and install Bommer mailboxes and accessories in quantities and at
locations
indicated on drawings.
U.S.P.S REGULATIONS: Materials sizes construction and installation shall comply with all current U.S.P.S. regulations.
LOCKS: Each
mail compartment door shall be provided with a lock keyed different
from
all other locks supplied for the project. A minimum of 1,000 key
changes
shall be available for the type lock supplied. Locks shall be:
(a) 5-pin tumbler cam
type
and shall be supplied with __ change keys per lock.
(b) spring bolt type which automatically latches when door is closed and shall be controlled by a 5-pin tumbler cylinder furnished with __ change keys per lock.
(c) spring bolt type
which
automatically latches when door is closed and shall be controlled by
cylinders
keyed into the building keying system. Cylinders adapted to fit mailbox
doors and locks are specified to be furnished by the hardware supplier
and shall be installed in doors by the mailbox manufacturer.

KEY KEEPER (model 5621
key
keeper shown at left)
A Bommer No. _____ Key Keeper with ____ finish shall
be provided at the entrance door to lobby.
LETTER DROP: A Bommer model 402 Letter Drop with ____ finish shall be provided at location indicated on drawings.
MAIL COLLECTION BOX: A Bommer No. _____ mail collection box with ____ finish shall be provided at location indicated on drawings.
HORIZONTAL
MAILBOXES
QUANTITIES AND ARRANGEMENT
OF
MAILBOXES shall be as indicated on construction drawings.
Shop
drawings showing fabrication and installation details shall be supplied
for approval prior to fabrication of mailboxes.
CONSTRUCTION: Mail compartments shall be double-wall type made of sheet aluminum. Frame members shall be heavy gauge extruded aluminum sections. Compartment doors shall be extruded aluminum not less than .156" thick reinforced at each edge with integral ribs. Doors shall swing on concealed pivots.
TYPE: Mailboxes
shall
be Bommer ______ Series Model No. ____ horizontal type. Units shall be:
(a) front loading. The
master
door shall be hinged to the units with a continuous stainless steel
hinge.
Single point locking shall be provided for master doors 4 or less
standard
compartments high; a spring-actuated latch at top and bottom shall be
provided
for master doors of greater height to provide 3-point locking. Access
to
latch shall be through one compartment door reserved for and designed
to
accommodate a lock supplied by the U.S.P.S.
Note: For
mailboxes not serviced by the U.S.P.S. substitute the following for the
last sentence of above paragraph:
Access to latch shall be through one compartment door and lock for this door shall be ... (1) 5-pin cam type ... (2) same type specified for doors of mail compartments.
(b) rear loading. Rear cover shall be made of sheet aluminum not less than .050" thick formed with a return at edges to provide rigidity and secured with latch bolts.
LOCKS: Bommer
offers three
(3) additional locks for horizontal mailboxes:
(a) removable core
cylinder
type. Complete lock assembly and removable core cylinders adapted to
fit
mailbox doors are specified to be furnished by the hardware supplier
and
shall be installed in doors by the mailbox manufacturer.
(b) combination type with spring latch bolt. Locks shall be 3-digit single dial type with automatic throw-off. Note: Combination locks are not approved for use on mailboxes serviced by employees of the U.S.P.S.
(c) 5-pin tumbler lock with high security 4-point locking system shall be supplied with 1 000 change keys per lock.
COMPARTMENT
IDENTIFICATION: Each
compartment shall be equipped with a channel type holder to accommodate
a name card for identifying the tenant using the box. Each door shall
be:
(a) provided with a slot
5/8" high by 2" wide fitted with a transparent plastic cover and steel
back plate and supplied with a standard cardboard strip on which room
or
apartment number can be printed by owner.
(b) supplied with room or apartment numbers 1/2" high engraved into face of door. Numbers shall be as directed by the architect or owner.
(c) provided with a slot 5/8" high and 2" wide fitted with a transparent plastic cover and steel back plate and supplied with a laminated black plastic strip engraved with white numbers. Numbers shall be as directed by the architect or owner.
(d) supplied with a 1-1/8" high x 2-1/2" wide x 3/16" thick Plexiglas window with room or apartment number 1/2" high engraved in window. Numbers shall be as directed by architect or owner. (Note: Windows are not approved for use in units serviced by employees of the U.S.P.S.)
TRIM: Peripheral trim 9/16" x 1-1/2" snap-on type extruded aluminum to match mailboxes shall be supplied with mailbox units.
DIRECTORIES
Shall be Bommer 6900 series designed to match
horizontal
mailboxes. Units shall be:
(a) top mounted type
___
of same width as mailboxes.
(b) side mounted or separate type 6921 of same height as mailboxes. A sufficient number of directory panels shall be supplied to provide one 3/8" name line per mail compartment plus 40 percent.
FINISH: Fronts of compartment door units shall: (a) be natural anodized aluminum 628. (b) have a ____ finish.
INSTALLATION: Mailbox
units and accessories shall be installed in accurately framed openings
with units plumb and adequately secured in position. Miscellaneous
blocking
and trim required for proper installation shall be furnished and
installed
by the contractor.
VERTICAL
MAILBOXES - 9040 Series USPS STD 4B+
CONSTRUCTION
Each mailbox shall consist of 3 to 7 compartments
enclosed
within a wall box. Both the compartments and wall box shall be
constructed
of not less than .028" galvanized and chromated steel riveted and spot
welded. Compartment doors and exposed frame members shall be made of
extruded
and anodized aluminum not less than .085" thick. Doors shall swing on
concealed
pivots. All exposed surfaces shall have a ___ finish.
MOUNTING FRAMES: (Optional:
for use where recessed mounting is not practical.)
Mounting frames shall be supplied for all mailbox
units.
Frames shall be:
(a) full-surface type
Bommer
No. 9341-X where X indicates number of
compartments.
For example 9341-7 = 7 gang.
(b) semi-recess type
Bommer
No. 9434-X where X indicates number of
compartments.
For example 9343-4 = 4 gang.
ALPHABETICAL
DIRECTORIES (Required in all
apartment
buildings having 15 or more mailbox compartments.)
Alphabetical Directory shall be Lee Dan model
AD-____.
Directory shall be provided in a separate frame or receptacle Lee Dan
model
AD-____made of aluminum and designed for surface installation.
INTERCOM LOBBY
PANELS
Intercom Lobby Panels shall be Lee Dan model ________
and shall be fabricated from ___ finish aluminum extrusions, or high
grade
(low carbon) stainless steel, or solid polished brass. Quantities and
arrangement of panels
shall
be as indicated on construction drawings. Panels shall be supplied
complete
with push-buttons as indicated.
INSTALLATION
Installation of units with push-buttons and speaker
panels
shall be coordinated with installation of wiring speakers etc.
specified
under electrical sections of the specification.

LEE DAN® COMMUNICATIONS, INC.
155 Adams
Avenue, Hauppauge, New York, 11788-3699 USA
Phone: 800-231-1414 or
631-231-1414, Fax: 631-231-1498, E-Mail: info@leedan.com
©1998-2010 Lee Dan Communications, Inc., All rights reserved. This page updated January 4, 2010