Lee Dan logo
 
 
 
 
 
Phone: 800-231-1414 or 631-231-1414 Fax: 631-231-1498 E-Mail: info@leedan.com

Elegant Solid Polished Brass - For Luxury and Historic Buildings

BS-022S
BS-022S Bravo™ Solid Polished Brass
Apartment Lobby Panel

22 Button Surface Mount

Bravo™ Solid Polished Brass
Apartment Lobby Panel

With Permanently Engraved, Individually Replaceable,
SOLID Black METAL Plungers

Bravo Panels are Available in the Following Button Styles:

Panel Sizes May Vary By Style

Bravo Classic
Two Tone Style
Centurion
Styling
Quantum
Styling

Black Metal Plungers

Plastic Buttons

 

Round Metal Buttons

Engraved # Strips

 

Round Metal Buttons

Engraved Brass

No Paint Fill

Use Bravo Size Chart Use Centurion Size Chart Use Quantum Size Chart

 

Standard BRAVO Features

  • Heavy .062 Solid Polished Brass
  • Three (3) Style Choices (See Above Chart)
  • Integral Polycarbonate Protected Alphabetical Directory
  • Exclusive 3-Layer Metal Speaker Baffle
  • Mylar Cone Weather-Resistant Speaker
  • Solid Permanently, Custom Engraved Black Metal Plungers
  • Self-Wiping Push Buttons with Screw Terminals
  • Push Buttons mounted on a Reinforced Backplate
  • Standard Engraved: 1-22 as shown
  • Custom Engraved: Upon Request, Such as 1A-11A, 1B-11B
  • Optional Building Address Engraving Deters Theft (add suffix 'E' to model no.)
  • Custom Sizing Available
  • 'Tampruf' Tamper-Proof Access Screws
  • Optional Lacquer, or allow panel to age for Antique Finish
Flush Mount
Model Available
Also Consider
Quantum Style Stainless Steel

Bravo Button Options:


See Spec Sheet

See Wiring Instructions

Size CLASSIC” BRAVO STYLE ONLY: 18 3/4" H x 10" W x 2 1/8" D
For Round Button Styles, Consult Factory
Material
Finish
Heavy .062 Solid Polished Brass
STANDARD: UN-Lacquered. . . ASK ABOUT OPTIONAL LACQUERED FINISH
Speaker 3 1/2", 1.0 Watt, 45 Ohm Mylar Cone, Weather-Resistant
Heavy duty magnet with natural voice reproduction
Also used for tone signal from lobby panel
Grille 3-layer metal speaker baffle
Buttons “Classic” Bravo Bravo Centurion Style Bravo Quantum Style
Solid permanently,
custom engraved black metal plungers
Heavy (6 amp rated) solid metal buttons
with positive screw terminals
Heavy (6 amp rated) solid metal buttons
with positive screw terminals
ST-008/2 Replacement Type ST-SSR2 Replacement Type ST-SSR2 Replacement Type
Holes 4 mounting holes, brass folded sides. Mounting brackets included.
Screws Includes 4 Tampruf tamper resistant mounting screws
Requires SC-T Tampruf tamper screw driver to install
Directory Strips
LDDS: LEE DAN Directory Strip 3 13/16" W x 1/4" H Up to 22 Characters
LDDS-B: Blank LDDS, Used for Spacing Between Names 3 13/16" W x 1/4" H Blank LDDS
LDDS-X: Broadcast Message Strip 3 13/16" W x 1" H Up to 4 Lines
Unlacquered vs. Lacquered Brass
BRAVO Custom Intercom Entry Panels Are Available In Two Finishes:
STANDARD Finish is Unlacquered.
This is a bright, shiny unprotected polished finish. Unlacquered panels will show every fingerprint, and smudge. Loss of its original luster will begin immediately, and will become more noticeable as a result of passage of time and natural day to day usage. As it reacts with oxygen and the elements, the unprotected brass finish will oxidize and develop a dark patina that some consider an antique-brass, or "bronzy" look. Depending on environmental conditions, it could take approximately two years to attain the darkest patina.
Lacquer is an OPTIONAL Finish.
This is a bright, shiny protected polished finish. Lacquered panels show fewer fingerprints and fewer smudges. Most importantly, lacquered panels may retain its original luster over years of normal use. Lacquer finishes will wear over time and are not considered permanent. Only the finished front of the panel is lacquered. Edges, mounting holes and other production holes may still be vulnerable to gradual oxidation. Lacquering is meant to protect a panels' bright, shiny luster, and should not be considered a guard against scratches or vandalism. Do not attempt to polish or clean lacquered panels, as this will damage the lacquer. As an added process, lacquering may add 1-3 weeks to standard production time.

Print Lacquer Information

Required Components

PK-543A (1 per Bldg)

Apartment Stations

SC-T "Tampruf" Screwdriver

Replaceable Parts

Buttons: Call Factory

SK-004

Directory Strips

 

Last modification time of the file: February 09 2021 16:34:42.